Utax cd 1116 Manuale di Servizio Pagina 194
- Pagina / 278
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
2DA/2DB
1-6-26
4. Insert the locating ball on each of the scanner
wires into the hole in the respective scanner
wire drum and wind the scanner wire three
turns inward and four turns outward.
•With the locating ball as the reference point,
wind the shorter end of each of the wires
outward.
5. Secure the scanner wires using the scanner
wire stoppers.
6. Refit the scanner wire drum shaft to the
scanner unit.
7. Insert the two frame securing tools into the
positioning holes at the front and rear of the
scanner unit to pin the mirror 2 frame in
position.
Three turns inward
Three turns inward
Four turns outward Four turns outward
Locating ball
Scanner wire drum
Scanner wire stoppers
Mirror 2 frame
Frame securing tool
Frame securing tool
Figure 1-6-47
Figure 1-6-48
- Service Manual 1
- Double-pole/neutral fusing 3
- Safety precautions 5
- 1. Installation Precautions 7
- 3. Miscellaneous 9
- CONTENTS 10
- 1-6 Assembly and Disassembly 12
- 2-1 Mechanical construction 13
- 2-2 Electrical Parts Layout 13
- 2-3 Operation of the PCBs 13
- 2-4 Appendixes 13
- 1-1-1 Specifications 14
- 0 Function key 17
- 1-1-3 Machine cross section 18
- 1-1-4 Drive system 19
- 1-2-1 Drum 20
- 1-2-2 Toner 20
- (1) Installation procedure 22
- Toner container release lever 26
- Toner container 26
- Positioning pins 28
- Cassette size 28
- Hole Hole 32
- Fixing fitting 33
- Bronze TP screws M3 x 06 33
- Axis section 36
- Duplex unit 37
- S tite screws 37
- Front right cover 39
- Power source PCB 41
- Wire of the drawer heater 41
- Upper left cover 45
- Inner cover 46
- Ejection cover 47
- Inner ejection cover 47
- Large ejection cover 50
- Staple cover 51
- TP bind screw M3 51
- Copy tray 52
- Front ejection cover 52
- Rear ejection 52
- Fitting part 53
- Left front 53
- Job separator 55
- Small pin 55
- Large pin 55
- Right hook 56
- Left front cover JS 57
- Fax control PCB assembly 58
- Mounting plate 58
- Ground wire 58
- Shield cover 59
- Modular cover 61
- Fax label sheet 63
- Cover plate 63
- Projection 64
- One-touch sheet 64
- FCC68 label 65
- Hard disk 68
- 1-4-1 Maintenance mode 69
- U053 U065 U070 84
- U034 U066 U071 85
- U034 U067 U072 86
- : 123 123 123 94
- : 255 255 255 94
- 1-4-2 Management mode 122
- 1-5-1 Paper misfeed detection 129
- Figure 1-5-2 130
- 1-5-2 Self-diagnosis 145
- See page 1-5-31 154
- (13)Paper creases. Causes 159
- 1-5-4 Electrical problems 162
- 1-5-5 Mechanical problems 167
- 1-6-2 Paper feed section 171
- Separation pulley 172
- Lower paper feed unit 172
- Separation pulley unit 172
- Registration guide 173
- Paper feeder 175
- Drawer separation pulley 176
- Drawer separation 176
- Upper paper feed unit 177
- Left cover 179
- Bypass upper cover 180
- Bypass lower cover 180
- Connector 180
- Bypass paper feed clutch gear 181
- Stop ring 181
- Bypass paper feed pulley unit 182
- Bypass separation pad 182
- Trans guide film 183
- Registration cleaner 183
- (P. 1-6-35) 184
- (P. 1-4-17) 184
- Original Copy 185
- (P. 1-6-36) 186
- (P. 1-4-18) 186
- Correct image Output 187
- Trailing edge margin 187
- –2.0–2.0 188
- Upper right cover 190
- Contact glass 190
- Exposure lamp 190
- Front scanner cover 191
- Slit retainer 191
- Slit glass 191
- Scanner tension springs 192
- Round terminal 192
- Scanner wire 193
- Scanner wire drum shaft 193
- Mirror 2 frame 194
- Frame securing tool 194
- Mirror 1 frame 195
- CCD wire 196
- Rear cover 197
- Right cover 197
- Front left cover 198
- Rear left 198
- Inner rear cover 198
- Exit cover 198
- Laser scanner 199
- (P. 1-6-18) 204
- (P. 1-6-20) 205
- (P. 1-4-44) 205
- 1-6-4 Drum section 206
- Main char 208
- Main charger 208
- Developing unit 209
- Transfer roller 210
- Fitting portion 210
- Paper conveying unit 210
- Front left cover 1 211
- Connectors 212
- Fixing left unit 213
- Fixing right unit 213
- heater S 214
- Fixing heater M 214
- Heat roller se 215
- Heat roller 216
- Heat roller bushing 216
- Fixing thermostat 217
- Compact Flash 219
- Notch hole 220
- 2-1-1 Paper feed section 222
- 2-1-2 Optical section 225
- 2-1-3 Drum section 229
- 2-1-4 Developing section 231
- 241
- 2-3-1 Power source PCB 246
- 120 V AC 247
- 220-240 V AC 247
- 2-3-2 Main PCB 249
- 2-3-3 Engine PCB 253
- 2-3-4 Printer board PCB 259
- 2-3-5 Operation unit PCB 263
- 2DA/2DB-1 264
- 2-3-6 CCD PCB 266
- × 17", two sheets 269
- Maintenance parts list 275
- General wiring diagram 278
Prodotti e manuali riguardandi Apparecchi multifunzione Utax cd 1116
(198 pagine)
(6 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale